RGX 2900

• Type: Brushless, Single Phase
• Voltage: 220-240V, 50Hz
• Rated Power: 2.0 KVA
• Max. Power: 2.4 KVA
• Fuel: Gasoline
• Tank Capacity: 12.8L
• Continuous Operating Hours: 12.0h
• Starting System: Recoil Starter
• Dimensions LxWxH (mm): 580 420x480
• Dry Weight: 48Kg

RGX 3600E

Technical Specifications:

• Type: Brushless, Single Phase
• Voltage: 220-240V, 50Hz
• Rated Power: 2.4 KVA
• Max. Power: 3.0 KVA
• Fuel: Gasoline
• Tank Capacity: 12.8L
• Continuous Operating Hours: 9.5h
• Starting System: Recoil/ Electric Starter
• Dimensions LxWxH (mm): 605x450x500
• Dry Weight: 54Kg

RG 3200iS

Technical Specifications:

• Type: Inverter
  
• Voltage: 220-240V, 50Hz
• Rated Power: 2800 W
• Max. Power: 3200 W
• Fuel: Gasoline
• Tank Capacity: 14L
• Continuous Operating Hours: 8.4h
• Starting System: Recoil/ Electric Starter
• Dimensions LxWxH (mm): 537x482x583
• Dry Weight: 59Kg
• Noise Level (rated at 7m): 58dB 

RG 4300iS

• Type: Inverter
  
• Voltage: 220-240V, 50Hz
• Rated Power: 3800 W
• Max. Power: 4300 W
• Fuel: Gasoline
• Tank Capacity: 16L
• Continuous Operating Hours: 6.6h
• Starting System: Recoil/ Electric Starter
• Dimensions LxWxH (mm): 580x527x618
• Dry Weight: 74Kg
• Noise Level (rated at 7m): 62dB

RGD 3300S-II

Technical Specifications:

• Type: Brushless, Single Phase
  
• Voltage: 220-240V, 50Hz
• Rated Power: 2.7 KVA
• Max. Power: 3.0 KVA
• Fuel: Diesel
• Tank Capacity: 11.5L
• Continuous Operating Hours: 10.6h
• Starting System: Electric Starter
• Dimensions LxWxH (mm): 722x538x667
• Dry Weight: 110Kg
• Noise Level (rated at 7m): 64.5 dBA

FV-7.5SKBS

Technical Specifications:

• Stand-by Output: 6.5 KW
• Prime Output: 5.6 KW
• Type: 2 Pole, Single Phase, Brushless
• Voltage: 200-240V, 50Hz
• Power Factor: 1
• Voltage Regulation System: AVR
• Engine: Kubota Z482
• Type: Vertical, Water Cooled, 4 cycle Diesel
• Rated Speed (min^-1): 3000
• Cylinders: 2
• Fuel: Diesel
• Tank Capacity: 20L
• Fuel Consumption (full load): 2.2L/h
• Fuel Consumption (70% load): 1.5L/h
• Starting System: Electric Starter
• Dimensions LxWxH (mm): 1050x600x690
• Dry Weight: 250Kg
• Sound Level (at 7m): 66dB

FV-11SKBS

• Stand-by Output: 9.7 KW
• Prime Output: 8.4 KW
• Type: 2 Pole, Single Phase, Brushless
• Voltage: 200-240V, 50Hz
• Power Factor: 1
• Voltage Regulation System: AVR
• Engine: Kubota D722
• Type: Vertical, Water Cooled, 4 cycle Diesel
• Rated Speed (min^-1): 3000
• Cylinders: 3
• Fuel: Diesel
• Tank Capacity: 20L
• Fuel Consumption (full load): 3.1L/h
• Fuel Consumption (70% load): 2.2L/h
• Starting System: Electric Starter
• Dimensions LxWxH (mm): 1250x640x690
• Dry Weight: 290Kg
• Sound Level (at 7m): 64dB

FV-14TKBS

Technical Specifications:

• Stand-by Output: 12.4 KVA
  
• Prime Output: 10.8 KVA
• Type: 2 Pole, Three Phase, Brushless
• Voltage: 400V, 50Hz
• Power Factor: 0.8
• Voltage Regulation System: AVR
• Engine: Kubota D722
• Type: Vertical, Water Cooled, 4 cycle Diesel
• Rated Speed (min^-1): 3000
• Cylinders: 3
• Fuel: Diesel
• Tank Capacity: 20L
• Fuel Consumption (full load): 3.1L/h
• Fuel Consumption (70% load): 2.2L/h
• Starting System: Electric Starter
• Dimensions LxWxH (mm): 1250x640x690
• Dry Weight: 290Kg
• Sound Level (at 7m): 64dB

FV-28TDKBS

• Stand-by Output: 22.0 KVA
• Prime Output: 20.0 KVA
• Type: 4 Pole, Three Phase, Brushless
• Voltage: 400V, 50Hz
• Power Factor: 0.8
• Voltage Regulation System: AVR
• Engine: Kubota V2203
• Type: Vertical, Water Cooled, 4 cycle Diesel
• Rated Speed (min^-1): 1500
• Cylinders: 4
• Fuel: Diesel
• Tank Capacity: 40L
• Fuel Consumption (full load): 5.4L/h
• Fuel Consumption (70% load): 3.8L/h
• Starting System: Electric Starter
• Dimensions LxWxH (mm): 1750x700x900
• Dry Weight: 610Kg
• Sound Level (at 7m): 63dB

Force 125

MMA inverter, electrode welding machine in direct current (DC). Use with a wide range of electrodes:rutile, basic, stainless steel, cast iron, etc. Characteristics: compact and light * high welding current stability in spite of mains voltage fluctuations * arc force, hot start and anti-stick devices * thermostatic, overvoltage, undervoltage, overcurrent, motorgenerator (+/- 15%) protections. Complete with TIGER helmet and MMA welding accessories. 

Technical Specifications:

• Voltage: 230V, 1Ph
• Current Range: 10-80A
• Duty Cycle: 5% @ 80A
• Power Consumption (Max): 2.3KW
• Weldable Electrodes: 1.6- 2.5mm
• Weight: 2.8Kg

Force 145

MMA inverter, electrode welding machine in direct current (DC). Use with a wide range of electrodes:rutile, basic, stainless steel, cast iron, etc. Characteristics: compact and light * high welding current stability in spite of mains voltage fluctuations * arc force, hot start and anti-stick devices * thermostatic, overvoltage, undervoltage, overcurrent, motorgenerator (+/- 15%) protections. Complete with TIGER helmet and MMA welding accessories.

Technical Specifications:

• Voltage: 230V, 1Ph
• Current Range: 10-130A
• Duty Cycle: 7% @125A
• Power Consumption (Max): 3.5KW
• Weldable Electrodes: 1.6- 3.2mm
• Weight: 2.8Kg

Tecnica 171/S

MMA and TIG inverter, electrode welding machine in direct current (DC) with scratch striking. Use with a wide range of electrodes: rutile, basic, stainless steel, cast iron, etc. Characteristics: compact and light * high welding current stability in spite of mains voltage fluctuations * arc force, hot start and anti-stick devices * thermostatic, overvoltage, undervoltage, overcurrent, motorgenerator (+/- 15%) protections. Complete with MMA welding accessories and plastic carry case.

Technical Specifications:

• Voltage: 230V, 1Ph
• Current Range: 10-150A
• Duty Cycle: 25% @140A
• Current at 60% Duty Cycle: 95A
• Power Consumption (60%): 2.6KW
• Power Consumption (Max): 4.2KW
• Weldable Electrodes: 1.6- 4.0mm
• Weight: 4.1Kg

Tecnica 211/S

MMA and TIG inverter, electrode welding machine in direct current (DC) with scratch striking. Use with a wide range of electrodes: rutile, basic, stainless steel, cast iron, etc. Characteristics: compact and light * high welding current stability in spite of mains voltage fluctuations * arc force, hot start and anti-stick devices * thermostatic, overvoltage, undervoltage, overcurrent, motorgenerator (+/- 15%) protections. Complete with MMA welding accessories and plastic carry case.

Technical Specifications:

• Voltage: 230V, 1Ph
• Current Range: 15-180A
• Duty Cycle: 18% @170A
• Current at 60% Duty Cycle: 105A
• Power Consumption (60%): 2.9KW
• Power Consumption (Max): 4.8KW
• Weldable Electrodes: 1.6- 4.0mm
• Weight: 4.1Kg

Nordika 2160

Single-phase, on wheels, fan-cooled stick electrode welding machine for MMA welding in alternating current (AC). Stepless regulation of welding current. With thermal protection. Usable electrodes: rutile. Complete with welding accessories. 

Technical Specifications:

• Voltage: 230V, 1Ph
• Current Range: 55-160A
• Power Consumption (Max): 2.5KW
• Weldable Electrodes: 2.0- 4.0mm
• Weight: 17.2Kg

Nordika 3200

Single-phase, on wheels, fan-cooled stick electrode welding machine for MMA welding in alternating current (AC). Stepless regulation of welding current. With thermal protection. Usable electrodes: rutile.

Technical Specifications:

• Voltage: 230-1Ph, 400V- 2Ph
• Current Range: 55-190A
• Power Consumption (Max): 3.5KW
• Weldable Electrodes: 2.0- 4.0mm
• Weight: 21Kg

Nordika 3250

Single-phase, on wheels, fan-cooled stick electrode welding machine for MMA welding in alternating current (AC). Stepless regulation of welding current. With thermal protection. Usable electrodes: rutile.

Technical Specifications:

• Voltage: 230-1Ph, 400V- 2Ph
• Current Range: 60-250A
• Power Consumption (Max): 4.2KW
• Weldable Electrodes: 2.0- 4.0mm
• Weight: 23Kg

Artika 270

MMA stick electrode welding machine in alternating current (AC). Stepless regulation of welding current. With thermostatic protection. Use with a wide range of electrodes: rutile.

Technical Specifications:

• Voltage: 230V-1Ph, 400V- 2Ph
• Current Range: 60-250A
• Duty Cycle: 10% @ 200A
• Current at 60% Duty Cycle: 80A
• Power Consumption (60%): 2.5KW
• Power Consumption (Max): 8.0KW
• Weldable Electrodes: 2.0- 5.0mm
• Weight: 26Kg

Quality 280 AC/DC

MMA stick electrode welding machine in direct (DC) and alternating current (AC). Stepless regulationof welding current. With thermostatic protection. Use with a wide range of electrodes: rutile, basic, stainless steel and cast iron.

Technical Specifications:

• Voltage: 230V-1Ph, 400V- 2Ph
• Current Range (AC): 45-230A
• Current Range (DC): 25-160A
• Duty Cycle (AC): 10% @ 220A
• Duty Cycle (DC): 15% @150A
• Current at 60% Duty Cycle (AC): 90A
• Current at 60% Duty Cycle (DC): 80A
• Power Consumption (60%): 3.3KW
• Power Consumption (Max): 7.2KW
• Weldable Electrodes (AC): 1.6- 5.0mm
• Weldable Electrodes (DC): 1.6-4.0mm
• Weight: 40Kg

Linear 220

MMA, rectified, electrode welding machine in direct current (DC). Stepless regulation of welding current. Use with a wide range of electrodes: rutile, basic, stainless steel, cast iron and aluminium.

Technical Specifications: 

• Voltage: 230-400V, 3Ph
• Current Range: 40-190A
• Duty Cycle: 35% @170A
• Current at 60% Duty Cycle: 120A
• Power Consumption (60%): 4.5KW
• Power Consumption (Max): 6.5KW
• Weldable Electrodes: 2.0- 4.0mm
• Weight: 55Kg

Linear 280

MMA, rectified, electrode welding machine in direct current (DC). Stepless regulation of welding current. Use with a wide range of electrodes: rutile, basic, stainless steel, cast iron and aluminium.

Technical Specifications:

• Voltage: 230-400V, 3Ph
• Current Range: 50-260A
• Duty Cycle: 25% @ 230A
• Current at 60% Duty Cycle: 140A
• Power Consumption (60%): 5.0KW
• Power Consumption (Max): 8.0KW
• Weldable Electrodes: 1.6- 5.0mm
• Weight: 65Kg

Linear 340

MMA, rectified, electrode welding machine in direct current (DC). Stepless regulation of welding current. Use with a wide range of electrodes: rutile, basic, stainless steel, cast iron and aluminium.

Technical Specifications:

• Voltage: 230-400V, 3Ph
• Current Range: 60-320A
• Duty Cycle: 25% @ 320A
• Current at 60% Duty Cycle: 180A
• Power Consumption (60%): 7.0KW
• Power Consumption (Max): 11.5KW
• Weldable Electrodes: 2.0- 6.0mm
• Weight: 80Kg

Linear 410/S

• Linear 410/S
• Industrial Range
• Three Phase Supply

Linear 430 HD

MMA, rectified, electrode welding machine in direct current (DC). Stepless regulation of welding current. Use with a wide range of electrodes: rutile, basic, stainless steel, cast iron and aluminium.

Technical Specifications:

• Voltage: 230-400V, 3Ph
• Current Range: 80-360A
• Duty Cycle: 35% @ 325A
• Current at 60% Duty Cycle: 240A
• Power Consumption (60%): 8.4KW
• Power Consumption (Max): 14KW
• Weldable Electrodes: 2.0- 6.0mm
• Weight: 101Kg

Telmig 180/2 Turbo

MIG-MAG welding machine. Designed for continuous and spot welding with electronic regulation of spotwelding time. Thanks to optional kits this model allows also sheet tempering and riveting. Flexibility of use with a wide range of materials such as steel, stainless steel, high strength steels and aluminium. Complete with MIG-MAG welding accessories.

Technical Specifications:

• Voltage: 230V, 1Ph
• Current Range: 30-170A
• Duty Cycle: 20% @ 140A
• Current at 60% Duty Cycle: 80A
• Power Consumption (60%): 2.3KW
• Power Consumption (Max): 5.2KW
• Steel Wire Diam: 0.6/0.8mm
• Stainless Steel Wire Diam: 0.8mm
• Aluminium Wire Diam: 0.8/1.0mm
• Weight: 38Kg

Mastermig 270/2

MIG-MAG/BRAZING welding machine. Designed for continuous and spot welding with electronic regulationof spot welding time. Thanks to optional kits this model allows also sheet tempering and riveting. Flexibility of use with a wide range of materials such as steel, stainless steel, high strength steels and aluminium. Complete with MIG-MAG welding accessories.

Technical Specifications:

• Voltage: 400V, 3Ph
• Current Range: 28-270A
• Duty Cycle: 30% @ 240A
• Current at 60% Duty Cycle: 160A
• Power Consumption (60%): 5.5KW
• Power Consumption (Max): 9.0KW
• Steel Wire Diam: 0.6-1.2mm
• Stainless Steel Wire Diam: 0.8-1.0mm
• Aluminium Wire Diam: 0.8-1.0mm
• Brazing Wire Diam: 0.8-1.0mm
• Weight: 68Kg

Mastermig 400

MIG-MAG/FLUX/BRAZING welding machine with removable wire feeder, fit for use in the industrial field. Flexibility of use with a wide range of materials such as steel, stainless steel, high strength steels and aluminium. Characteristics: very strong * numerous steps for regulation of arc voltage * regulation of spot welding time * two positions for reactance * thermostatic protection. Thanks to the extensions (optional) it is possible to increase the working range between wire feederand power source up to 10 meters. Complete with MIG-MAG welding accessories.

Technical Specifications:

• Voltage: 400V, 3Ph
• Current Range: 50-400A
• Duty Cycle: 25% @ 400A
• Current at 60% Duty Cycle: 240A
• Power Consumption (60%): 6.0KW
• Power Consumption (Max): 11.5KW
• Steel Wire Diam: 0.6-1.6mm
• Stainless Steel Wire Diam: 0.8-1.6mm
• Aluminium Wire Diam: 0.8-1.2mm
• Flux Cored Wire Diam: 1.0-1.2mm
• Brazing Wire Diam: 0.8-1.2mm
• Weight: 104Kg

Supermig 480

MIG-MAG/FLUX/BRAZING welding machine with 4 rolls, separate wire feeder, fit for use in the industrial field. Flexibility of use with a wide range of materials such as steel, stainless steel and aluminium. Characteristics: very strong * numerous steps for regulation of arc voltage * 2/4 strokes torch pushbutton selector * regulation of spot welding time, wire speed up slope, wire burn-back time * two positions for reactance * thermostatic protection. Thanks to the extensions (optional) it is possible to increase the working range between wire feeder and power source up to 10 meters. Complete with MIG-MAG welding accessories.

Technical Specifications:

• Voltage: 400V, 3Ph
• Current Range: 50-420A
• Duty Cycle: 25% @ 420A
• Current at 60% Duty Cycle: 300A
• Power Consumption (60%): 11KW
• Power Consumption (Max): 19KW
• Steel Wire Diam: 0.8-2.0mm
• Stainless Steel Wire Diam: 0.8-2.0mm
• Aluminium Wire Diam: 0.8-1.2mm
• Flux Cored Wire Diam: 1.0-2.0mm
• Brazing Wire Diam: 0.8-1.2mm
• Weight: 122Kg

Technomig 200

Microprocessor controlled, MIG-MAG/FLUX/BRAZING,TIG-DC LIFT and MMA inverter welding machine. The SYNERGIC function allows for a rapid and easy setting of the welding programmes and grants always a high control both of the arc and of the quality of the welding. The synergy and the remote regulation of the welding parameters make it particularly suitable for use in the industrial field. Particularly suitable for welding aluminium, galvanised sheets, HSS high strength steels, stainless steel. Characteristics: 15 standard and possibility to store 10 customized welding programmes * regulation of post gas, current down slope, burn-back time * choice of 2/4 times, spot operation * arc force, hot start, anti-stick devices * remote control connector * automatic torch recognition * check control at starting * storage on on-board E2PROM of the last 10 alarms * thermostatic, overvoltage, undervoltage, overcurrent protections * use with SPOOL GUN torch. Complete with MIG-MAGwelding accessories.

Technical Specifications:

• Voltage: 230V, 1Ph
• Current Range: 5-200A
• Duty Cycle: 30% @ 200A
• Current at 60% Duty Cycle: 140A
• Power Consumption (60%): 3.5KW
• Power Consumption (Max): 5.5KW
• Steel Wire Diam: 0.6-1.0mm
• Stainless Steel Wire Diam: 0.8-1.0mm
• Aluminium Wire Diam: 0.8-1.0mm
• Flux Cored Wire Diam: 0.8-1.2mm
• Brazing Wire Diam: 0.8mm
• Weldable Electrodes: 1.6- 4.0mm
• Weight: 26Kg

Tecnica Tig 160 DC-HF/LIFT

TIG (high frequency HF or LIFT striking) and MMA inverter welding machine in direct current (DC). Use with a wide range of materials such as steel, stainless steel, titanium, copper, nickel and their alloys. Characteristics: compact and light * TIG regulations: current down slope * MMA regulations: arc force according to the type of electrode in use * 2/4 strokes operation * hot startand anti-stick devices * remote control connector * MMA electrodes: rutile, basic, stainless steel and cast iron * thermostatic, overcurrent, overvoltage, undervoltage protections. Complete with TIG welding accessories and aluminium carry case.

Technical Specifications:

• Voltage: 230V, 1Ph
• Current Range: 5-130A
• Duty Cycle: 15% @130A
• Current at 60% Duty Cycle: 75A
• Power Consumption (60%): 1.7KW
• Power Consumption (Max): 3.7KW
• Weldable Electrodes: 1.6- 3.2mm
• Weight: 4.8Kg

Technology Tig 230 DC-HF/LIFT

TIG (high frequency HF or LIFT striking) and MMA inverter welding machine in direct current (DC). Use with a wide range of materials such as steel, stainless steel, titanium, copper, nickel and their alloys. Characteristics: TIG regulations: current down slope, bi-level * MMA regulations: arc force according to the type of electrode in use * 2/4 strokes operation * hot start and anti-stick devices * remote control connector * MMA electrodes: rutile, basic, stainless steel and cast iron * thermostatic, overcurrent, overvoltage, undervoltage protections. The optional TIG PULSE allows pulse welding. Complete with TIG welding accessories.

Technical Specifications:

• Voltage: 230V, 1Ph
• Current Range: 5-220A
• Duty Cycle: 30% @ 220A
• Current at 60% Duty Cycle: 125A
• Power Consumption (60%): 3.6KW
• Power Consumption (Max): 5.5KW
• Weldable Electrodes: 1.6- 4.0mm
• Weight: 8.5Kg

Technology Tig 182 AC/DC-HF/LIFT

Microprocessor controlled, TIG (high frequency HF or LIFT striking), PULSE TIG and MMA inverter welding machine in direct and alternating current (AC/DC). Use with a wide range of materials such as steel, stainless steel, aluminium, titanium, copper, nickel, magnesium and their alloys. Characteristics: TIG regulations: post gas, current down slope/time, bi-level, balance * MMA regulations: arc force according to the type of electrode in use * 2/4 times operation * hot start and anti-stick devices * remote control connector * MMA electrodes: rutile, basic, stainless steel and cast iron * thermostatic, overcurrent, overvoltage, undervoltage protections. Complete with TIG welding accessories.

Technical Specifications:

• Voltage: 230V, 1Ph
• Current Range: 5-160A
• Duty Cycle: 20% @ 160A
• Current at 60% Duty Cycle: 85A
• Power Consumption (60%): 2.5KW
• Power Consumption (Max): 4.3KW
• Weldable Electrodes: 1.6- 3.2mm
• Weight: 9.4Kg

Superior Tig 312 AC/DC-HF/LIFT

Technical Specifications:

• Voltage: 400V, 3Ph
• Current Range: 10-270
• Max Current: 40% at 270A
• Power Consumption (Max): 10KW
• Max MMA Electrode Diameter: 5mm
• Dimensions: 53x24x45mm
• Weight: 36Kg

Superior 400CE

• Superior 400CE
• Industrial Range
• Three Phase Supply

Supertig 200 AC/DC-HF

TIG (high frequency HF striking) and MMA welding machine in direct and alternating current (AC/DC). Use with a wide range of materials such as steel, stainless steel, aluminium, titanium, copper, nickel, magnesium and their alloys. Characteristics: continuous current regulation by magnetic shunt* post-gas regulation * 2/4 strokes TIG and MMA operation * MMA electrodes: rutile, basic, stainlesssteel and cast iron * thermostatic protection. Complete with TIG welding accessories.

Technical Specifications:

• Voltage: 400V, 2Ph
• Current Range (AC): 30-180A
• Current Range (DC): 25-150A
• Duty Cycle (AC): 15% @170A
• Duty Cycle (DC): 25% @140A
• Current at 60% Duty Cycle (AC): 75A
• Current at 60% Duty Cycle (DC): 85A
• Power Consumption (60%): 1.7KW
• Power Consumption (Max): 6.0KW
• Weight: 69Kg

Supertig 280 AC/DC-HF/LIFT

Thyristor-controlled, TIG (high frequency HF and LIFT striking) and MMA welding machine in direct and alternating current (AC/DC). Use with a wide range of materials such as steel, stainless steel, aluminium, titanium, copper, nickel, magnesium and their alloys. Characteristics: visualization on digital display and regulation of the following parameters: welding current, start current in 4 strokes TIG mode, pre gas, post-gas, current down slope, balance * 2/4 strokes TIG and MMA operation* remote control connector. * MMA electrodes: rutile, basic, stainless steel and cast iron * thermostatic protection. The optional device TIG PULSE allows pulse welding. Complete with TIG welding accessories.

Technical Specifications:

• Voltage: 400V, 2Ph
  
• Current Range: 15-250A
• Duty Cycle (DC): 30% @250A
• Current at 60% Duty Cycle (AC): 170A
• Current at 60% Duty Cycle (DC): 180A
• Power Consumption (60%): 6.1KW
• Power Consumption (Max): 10.5KW
• Weight: 97Kg
•  

Maxy Oxygen

Technical Specifications:

• Pressure reducer: class 3
• Outlet: 1/4'
• Outlet pressure: 10 bar
• Standard delivery flow: 30 m³/h
• Dimensions (LxWxH): 41x29x22 cm

Maxy Acetylene

• Pressure reducer: class 2 
• Outlet: Yoke 1/4'
• Outlet pressure: <1,5 bar
• Standard delivery flow: 5 m³/h
• Dimensions (LxWxH): 41x29x22 cm
• Weight: 1.7 kg

Maxy Argon-CO2

• Pressure reducer: class 1
• Outlet: CO₂ 1/4'
• Outlet pressure: 4 bar
• Standard delivery flow: <1.5 m³/h 
• Dimensions (LxWxH): 41x29x22 cm
• Weight: 1.3 kg 

Maxi Flux Argon-C02

A professional pressure reducer at reduced costs. Designed and manufactured ensure accurate and safe use of gases.

Ideal to fit welding machines MIG/MAG-TIG where robustness and high flow rates stability are required. Designed for intermediate pressures, gives high gas saving. It is equipped with flow meter with scale 0-30 l/min, in the version with preset delivery flow or with adjustment knob.

Technical Specifications:

• K pressure reducer class 1
• P2 outlet pressure 3.5 bar
• Q1 standard delivery flow > 2m³/h

Maxi 2 Flux Argon-C02

A very sturdy structure for a pressure reducer with bottom adjusting knob and side entry, designed and built to ensure a precise and safe use of gases. Ideal to fit welding machines MIG/MAG which require robustness and high flow rates stability. The side adjusting knob ensures a high flow stability.

Mini LP Gauge Argon-CO2

Compact pressure reducer, designed and manufactured for MIG/MAG-TIG welding machines. Thanks to its high reliability and its small size, it has become a standard device to fit portable equipment.

Ideal for:

• small portable gas welding equipment
• professional MIG/MAG-TIG welding machines
• special applications 

Technical Specifications:

• Pressure reducer: class 1
• Outlet pressure: 4 bar
• Standard delivery flow: <1 m³/h
• Dimensions (LxWxH): 41x36x24 cm
• Weight: 0.6 kg

Technology Plasma 41

Inverter, compressed air plasma cutting system, with contact striking of pilot arc. Allows a rapid, distortion-proof cutting of all conductive materials such as steel, stainless steel, galvanised steel, aluminium, copper, brass, etc. Characteristics: reduced weight and dimensions * warning led for torch under voltage, protections * torch automatic cooling * visualization of air pressure * thermostatic, overvoltage, undervoltage, overcurrent protections. Complete with torch.

Technical Specifications:

• Voltage: 230V, 1Ph
• Current Range: 7-40A
• Duty Cycle: 30% @ 35A
• Power Consumption (Max): 4KW
• Max Cutting Thickness: 12mm
• Compressed Air Capacity: 100L/min
• Compressed Air Pressure: 4-5 Bars
• Weight: 7.7Kg

Technology Plasma 54 Kompressor

Inverter, compressed air plasma cutting system, with contact striking of pilot arc. Allows a rapid, distortion-proof cutting of all conductive materials such as steel, stainless steel, galvanised steel, aluminium, copper, brass, etc. The model is equipped with a compressor and needs not to be connected to an external compressed air power source. Characteristics: reduced weight and dimensions* warning led for torch under voltage, protections * torch automatic cooling * thermostatic, overvoltage, undervoltage, overcurrent protections. Complete with torch.

Technical Specifications:

• Voltage: 230V, 1Ph
• Current Range: 7-40A
• Duty Cycle: 30% @ 35A
• Power Consumption (Max): 4.5KW
• Max Cutting Thickness: 10mm
• Weight: 16.8Kg

Superior Plasma 60HF

Inverter, compressed air plasma cutting system with high frequency HF striking of pilot arc. Allows a rapid, distortion-proof cutting of all conductive materials such as steel, stainless steel, galvanised steel, aluminium, copper, brass, etc. Possibility to use long nozzles. Characteristics: reduced weight and dimensions * possibility to cut on grids with automatic restart of pilot arc * warning led for torch under voltage, air fault, protections * control of torch cooling * visualization of air pressure * storage on on-board E2PROM of the last 10 alarms * thermostatic, overvoltage, undervoltage, overcurrent, torch shortcircuit, phase failure protections. Complete withtorch.

Technical Specifications:

• Voltage: 400V, 3Ph
• Current Range: 15-60A
• Duty Cycle: 35% @ 60A
• Power Consumption (Max): 7.5KW
• Max Cutting Thickness: 20mm
• Compressed Air Capacity: 120L/min
• Compressed Air Pressure: 4-5 Bars
• Weight: 19.4Kg

Superior Plasma 90HF

Inverter, compressed air plasma cutting system with high frequency HF striking of pilot arc. Allows a rapid, distortion-proof cutting of all conductive materials such as steel, stainless steel, galvanised steel, aluminium, copper, brass, etc. Possibility to use long nozzles. Characteristics: reduced weight and dimensions * possibility to cut on grids with automatic restart of pilot arc * warning led for torch under voltage, air fault, protections * control of torch cooling * visualization of air pressure * storage on on-board E2PROM of the last 10 alarms * thermostatic, overvoltage, undervoltage, overcurrent, torch shortcircuit, phase failure protections. Complete withtorch.

Technical Specifications:

• Voltage: 400V, 3Ph
• Current Range: 20-90A
• Duty Cycle: 40% @ 90A
• Power Consumption (Max): 12KW
• Max Cutting Thickness: 30mm
• Compressed Air Capacity: 200L/min
• Compressed Air Pressure: 4-5 Bars
• Weight: 30Kg

Superplasma 83 HF

• Mains Voltage: 230-400 V 3ph
  
• Current Range: 40 – 80 A
• Max. Current: 40 - 70  A 35%
• Max. No Load Voltage: 247 V
• Max. Absorbed Power: 11.5 Kw
• Power Factor: 0.6 cos Φ
• Max. Cutting Thickness: 20 mm
• Compressed Air Capacity: 150 L/min
• Compressed Air Pressure: 4 – 5 Bar
• Protection Degree: IP22
• Dimensions: 960 x 340 x 820 (mm)
• Weight: 89 Kg

SuperPlasma 130 HF

• Compressed air plasma cutting system with high frequency HF striking of pilot arc. Allows a rapid, distortion-proof cutting of all conductive materials, such as steel, stainless steel, galvanised steel, aluminium, copper, brass, etc. Possibility to use long nozzles. Characteristics: 2 positions for regulation of cutting current * control devices for torch under voltage, air pressure, torch short circuit, phase failure, thermostatic protection * possibility to cut on grids with automatic restart of pilot arc (self restart) * visualizaton of air pressure. Complete with torch
•  
• Technical Specifications:
   
• Voltage: 400V, 3Ph
• Current Range: 65-120A
• Duty Cycle: 40% @ 115A
• Power Consumption (Max): 20KW
• Max Cutting Thickness: 30mm
• Compressed Air Capacity: 200L/min
• Compressed Air Pressure: 4-5 Bars
• Weight: 86Kg

Enterprise Plasma 160 HF

Chopper, compressed air plasma cutting system, with high frequency HF striking of pilot arc. Allows a rapid, distortion-proof cutting of all conductive materials such as steel, stainless steel, aluminium, copper, brass. Possibility to use long nozzles. Characteristics: possibility to cut on grids with automatic restart of pilot arc * warning led for torch under voltage, air fault, protections * control of torch cooling * visualization of air pressure * storage of the last 10 alarms * thermostatic, overvoltage, undervoltage, overcurrent, torch shortcircuit, phase failure protections. Complete with torch.

Technical Specifications:

• Voltage: 400V, 3Ph
• Current Range: 20-160A
• Duty Cycle: 40% @ 160A
• Power Consumption (Max): 25KW
• Max Cutting Thickness: 45mm
• Compressed Air Capacity: 200L/min
• Compressed Air Pressure: 4-5 Bars
• Weight: 123Kg

AluCar 5100

Power source for capacitor discharge welding of studs of 3 and 4 mm diameter and other accessories, with tip strike. It is suitable for applications in car body shops. It enables welding of studs on non-treated or non oxidized surfaces in steel, stainless steel, galvanized steel, brass and, in particular, aluminium. The welding process is so short that it causes no alteration to the opposing surface even if painted, plastic-coated or galvanized. Complete with gun, earth cable with clamp andaccessories.

Technical Specifications:

• Voltage: 230V, 1Ph
• Power Consumption: 0.25 KW
• Spot Energy: 390 J max
• Spot Time: 1 to 3ms
• Number of Spottable Studs: 7 studs/ min
• Spottable Stud Diameter: 3 to 4mm
• Weight: 11.7 Kg

AluSpotter 6100

Power source for capacitor discharge welding of studs of 3 to 8 mm diameter and other accessories, with tip strike. It is suitable for applications in heating systems, installation and maintenance works. It enables welding of studs on non-treated or non oxidized surfaces in steel, stainless steel, galvanized steel, brass and, in particular, aluminium. The welding process is so short that it causes no alteration to the opposing surface even if painted, plastic-coated or galvanized. 115-230V automatic voltage reversal. Complete with gun, earth cable with clamp and accessories.

Technical Specifications:

• Voltage: 230V, 1Ph
• Power Consumption: 0.9 KW
• Spot Energy: 1500 J max
• Spot Time: 1 to 3ms
• Number of Spottable Studs: 20 studs/ min
• Spottable Stud Diameter: 3 to 8mm
• Weight: 15.7 Kg

Digital Car Spotter 5500

Microprocessor controlled, spot-welding machine fit for applications in car body shops. The digital,multifunction control panel allows the automatic regulation of spot welding parameters according to the chosen tool and sheet thickness. It is equipped with the "STUDDER" kit for spot welding of screws, washers, rivets and special washers, sheet warming and upsetting.

Technical Specifications:

• Voltage: 230V, 1Ph or 400V, 2Ph
• Power Consumption 50%: 2.8 KW
• Power Consumuption Max: 11 KW
• Spot Welding Thickness (2 sides): 1.5 + 1.5mm
• Weight: 29 Kg

Digital Spotter 9000 R.A

Microprocessor controlled, spot-welding machine suitable for use in car body repair and industrial field. The digital, multifunction control panel allows the automatic regulation of spot welding parameters according to the chosen tool and sheet thickness. Characteristics: automatic identification of the tool * monitoring of mains voltage * automatic control of the clamp and cable cooling * choice of optimal spot-welding current according to mains power. Equipped with water cooled pneumatic clamp, water cooling system and trolley 

Technical Specifications:

• Voltage: 400V, 2Ph
• Power Consumption 50%: 13 KW
• Power Consumuption Max: 40 KW
• Spot Welding Thickness (2 sides): 3 + 3mm
• Weight: 105 Kg

Modular 20 TI

Spot welding machine with electronic control of the spot welding time. Suitable for spot welding of sheets with maximum thickness 1+1mm. Characteristics: synchronous electronic timer with spot weldingtime adjustable from 0,1 sec. to 1,2 sec.* arms pressure adjustable from 40 kg to 120 kg (with arms L= 120 mm) * handgrip made out of thermic isolating material.

Technical Specifications:

• Voltage: 230V, 1Ph
• Power Consumption 50%: 1.2 KW
• Power Consumuption Max: 6 KW
• Spot Welding Thickness (2 sides): 1 + 1mm
• Weight: 10 Kg

Digital Modular 230

Microprocessor controlled, spot welding machine. It implements a new Fuzzy logic control system thatsimplifies its use and increases the spot welding quality. Suitable for spot welding of sheets with maximum thickness 2+2mm. Characteristics: automatic regulation of the spot welding current and time according to the material thickness * choice between continuous and pulse operation (suitable for sheets with high yield points - high stress) * arms pressure adjustable from 40 kg to 120 kg (with arms L= 120 mm) * handgrip made out of thermic isolating material * thermal protection.

Technical Specifications:

• Voltage: 230V, 1Ph
• Power Consumption 50%: 2.3 KW
• Power Consumuption Max: 13 KW
• Spot Welding Thickness (2 sides): 2 + 2mm
• Weight: 10.5 Kg

PTE 18

Column spot welder with movable arms and built-in synchronous control by thyristors. It grants optimum results on different kinds of steel. Characteristics: adjustment of spot welding current (from 20 to 100 %), spot welding time (from 1 to 100 cycles), electrode pressure * pedal control with adjustable spring. The model requires water cooling for electrodes and arms.

Technical Specifications:

• Voltage: 400V, 2Ph
• Power Consumption: 15 KVA
• Spot welding Thickness: 3 +3 mm
• Duty Cycle: 15%
• Dimensions: 790x 320x 1280 mm
• Weight: 115 Kg

PTE 28

Column spot welder with movable arms and built-in synchronous control by thyristors. It grants optimum results on different kinds of steel. Characteristics: adjustment of spot welding current (from 20 to 100 %), spot welding time (from 1 to 100 cycles), electrode pressure * pedal control with adjustable spring. The model requires water cooling for electrodes and arms.

Technical Specifications:

• Voltage: 400V, 2Ph
• Power Consumption: 25 KVA
• Spot welding Thickness: 5 +5 mm
• Duty Cycle: 5.5%
• Dimensions: 790x 320x 1280 mm
• Weight: 141 Kg

PCP 18

Column spot welder with movable arms and built-in synchronous control by thyristors. It grants optimum results on different kinds of steel. Characteristics: adjustment of spot welding current (from 20 to 100 %), spot welding time (from 1 to 100 cycles), electrode pressure * pneumatic compressed air control. The model requires water cooling for electrodes and arms.

Technical Specifications:

• Voltage: 400V, 2Ph
• Power Consumption: 15 KVA
• Spot welding Thickness: 3 +3 mm
• Duty Cycle: 15%
• Dimensions: 790x 320x 1280 mm
• Weight: 109 Kg

PCP 28

Column spot welder with movable arms and built-in synchronous control by thyristors. It grants optimum results on different kinds of steel. Characteristics: adjustment of spot welding current (from 20 to 100 %), spot welding time (from 1 to 100 cycles), electrode pressure * pneumatic compressed air control. The model requires water cooling for electrodes and arms.

Technical Specifications:

• Voltage: 400V, 2Ph
• Power Consumption: 25 KVA
• Spot welding Thickness: 5 +5 mm
• Duty Cycle: 5.5%
• Dimensions: 790x 320x 1280 mm
• Weight: 145 Kg

Mototronic 6/12

Battery charger with electronic control of charging current, automatic interruption and restart (TRONIC). Equipped with warning leds for correct mains voltage and polarity reversal of the battery.Fit for charging maintenance free, sealed batteries (GEL/AGM) and free-electrolyte batteries (WET) with 6/12V voltage of scooters and motorcycles. A special device (BY-PASS) allows the charge even with extremely low or sulphated batteries.

Technical Specifications:

• Mains Voltage: 230V, 1Ph
• Power: 50 W
• Voltage: 6-12 V
• Charge Current: 4 A
• Rated Charge Current: 2.5 A
• Rated Reference Capacity (Min/Max): 4/20 Ah 15h (6V), 6/30 Ah 15h (12V)
• Weight: 1.8 Kg

Nevatronic 12

Battery charger with electronic control of charging current, automatic interruption and restart (TRONIC). Equipped with warning leds for correct mains voltage and polarity reversal of the battery.Fit for charging maintenance free sealed batteries (GEL/AGM) and free-electrolyte batteries (WET) with 12V voltage of motorcycles, cars, light trucks and boats.

Technical Specifications:

• Mains Voltage: 230V, 1Ph
• Power: 90 W
• Voltage: 12 V
• Charge Current: 6 A
• Rated Charge Current: 4 A
• Rated Reference Capacity (Min/Max): 40/50 Ah 15h
• Weight: 2.1 Kg

Nevatronic 24

Battery charger with electronic control of charging current, automatic interruption and restart (TRONIC). Equipped with warning leds for correct mains voltage and polarity reversal of the battery.Fit for charging maintenance free sealed batteries (GEL/AGM) and free-electrolyte batteries (WET) with 12/24V voltage of motorcycles, cars, light trucks and boats.

Technical Specifications:

• Mains Voltage: 230V, 1Ph
• Power: 110 W
• Voltage: 12-24 V
• Charge Current: 6A (12V), 4.5A (24V)
• Rated Charge Current: 4A (12V), 3A (24V)
• Rated Reference Capacity (Min/Max): 40/55 Ah 15h (12V), 30/45 Ah 15h (24V)
• Weight: 2.2 Kg

Apline 13

Battery charger for charging free electrolyte batteries (WET) with 12V voltage. Protected against overloads and polarity reversal. Equipped with ammeter.

Technical Specifications:

• Mains Voltage: 230V, 1Ph
• Power: 80 W
• Voltage: 12 V
• Charge Current: 6 A
• Rated Charge Current: 4 A
• Rated Reference Capacity (Min/Max): 40/70 Ah 15h
• Weight: 2.7 Kg

Alpine 18 Boost

Battery charger for charging free electrolyte batteries (WET) with 12/24V voltage. Protected againstoverloads and polarity reversal. Equipped with selector for normal or quick (BOOST) charge. Equippedwith ammeter.

Technical Specifications:

• Mains Voltage: 230V, 1Ph
• Power: 200 W
• Voltage: 12-24 V
• Charge Current: 14A (12V), 8A (24V)
• Rated Charge Current: 9A (12V), 5A (24V)
• Rated Reference Capacity (Min/Max): 14/185 Ah 15h (12V), 6/90 Ah 15h (24V)
• Weight: 3.7 Kg 

Alpine 20 Boost

Battery charger for charging free electrolyte batteries (WET) with 12/24V voltage. Protected againstoverloads and polarity reversal. Equipped with selector for normal or quick (BOOST) charge. Equippedwith ammeter.

Technical Specifications:

• Mains Voltage: 230V, 1Ph
• Power: 300 W
• Voltage: 12-24 V
• Charge Current: 18A (12V), 12A (24V)
• Rated Charge Current: 12A (12V), 8A (24V)
• Rated Reference Capacity (Min/Max): 30/225 Ah 15h (12V), 20/180 Ah 15h (24V)
• Weight: 6.4 Kg

Alpine 30 Boost

Battery charger for charging free electrolyte batteries (WET) with 12/24V voltage. Protected againstoverloads and polarity reversal. Equipped with selector for normal or quick (BOOST) charge. Equippedwith ammeter.

Technical Specifications:

• Mains Voltage: 230V, 1Ph
• Power: 800 W
• Voltage: 12-24 V
• Charge Current: 30 A
• Rated Charge Current: 20 A
• Rated Reference Capacity (Min/Max): 15/400 Ah 15h
• Weight: 8.7 Kg

Autotronic 25 Boost

Battery charger with electronic control of the charging current, automatic interruption and restart (TRONIC), for charging lead-acid batteries with 12/24V voltage. Fit with switches to choose either anormal charge (MIN) or quick charge (BOOST) in the buffer mode (TRONIC) or drooping characteristic mode (CHARGE). The buffer automatic charge is adequate for maintenance free sealed batteries (GEL/AGM), while the drooping characteristic charge is adequate for free-electrolyte batteries (WET). Characteristics: choice of output voltage, type of charge, charging mode * display of charging current * protection against overloads and polarity reversal.

Technical Specifications:

• Mains Voltage: 230V, 1Ph
• Power: 300 W
• Voltage: 12-24 V
• Charge Current: 18A (12V), 12A (24V)
• Rated Charge Current: 12A (12V), 8A (24V)
• Rated Reference Capacity (Min/Max): 30/225 Ah 15h (12V), 20/180 Ah 15h (24V)
• Weight: 6.5 Kg

Digitrony 230 Start

Digital battery charger and starter with electronic control of the charging current, automatic interruption and restart (TRONIC). Normal (CHARGE), automatic (TRONIC), quick (BOOST) charge of all types of maintenance free, sealed batteries (GEL/AGM), free electrolyte batteries (WET) with 12/24V voltages and starting of cars, vans and light trucks. Characteristics: display to check charging current, voltage and battery charging level * choice of TEST, CHARGE, TRONIC mode * choice of outputvoltage, type of charge, charging mode * protection against overloads and polarity reversal.

Technical Specifications:

• Mains Voltage: 230V, 1Ph
• Charge/Start Absorbed Power: 0.8/ 3.6 KW
• Voltage: 12-24 V
• Charge Current: 30 A
• Rated Charge Current: 20 A
• Starting Peak Current: 180 A
• Rated Reference Capacity (Min/Max): 30/400 Ah 15h
• Weight: 9.5 Kg

Digistart 340

Digital battery charger and starter with electronic control of the charging current, automatic interruption and restart (PULSE-TRONIC) for charging all types of maintenance free, sealed batteries(GEL/AGM), free electrolyte batteries (WET) with 12/24V voltages and quick starting of cars, vans and light trucks. Characteristics: microprocessor control * display to check charging current, voltage and battery charging level * choice of TEST, CHARGE, TRONIC mode * CHARGE function: constantcurrent charge as set on the front panel * choice of output voltage, type of charge, charging mode * protection against overloads and polarity reversal.

Technical Specifications:

• Mains Voltage: 230V, 1Ph
• Current Range: 1-30 A
• Charge/Start Absorbed Power: 1/ 6.4 KW
• Voltage: 12-24 V
• Charge Current: 45 A
• Rated Charge Current: 30 A
• Starting Peak Current: 300 A
• Rated Reference Capacity (Min/Max): 10/450 Ah 15h
• Weight: 13.8 Kg

Dynamic 320 Start

Battery charger and starter for charging free electrolyte batteries (WET) with 12/24V voltage and starting all kinds of cars, vans and light trucks. Characteristics: choice of normal charge, quick charge (BOOST), quick start * display of charging and starting current * protection against overloads and polarity reversal.

Technical Specifications:

• Mains Voltage: 230V, 1Ph
• Charge/Start Absorbed Power: 0.8/ 3.6 KW
• Voltage: 12-24 V
• Charge Current: 30 A
• Rated Charge Current: 20 A
• Starting Peak Current: 180 A
• Rated Reference Capacity (Min/Max): 30/400 Ah 15h
• Weight: 13.3 Kg

Dynamic 420 Start

Battery charger and starter for charging free electrolyte batteries (WET) with 12/24V voltage and starting all kinds of cars, vans and light trucks. Characteristics: choice of normal charge, quick charge (BOOST), quick start * display of charging and starting current * protection against overloads and polarity reversal.

Technical Specifications:

• Mains Voltage: 230V, 1Ph
• Charge/Start Absorbed Power: 1/ 6.4 KW
• Voltage: 12-24 V
• Charge Current: 45 A
• Rated Charge Current: 30 A
• Starting Peak Current: 300 A
• Rated Reference Capacity (Min/Max): 20/700 Ah 15h
• Weight: 13.9 Kg

Dynamic 520 Start

Battery charger and starter for charging free electrolyte batteries (WET) with 12/24V voltage and starting all kinds of cars, vans and light trucks. Characteristics: choice of normal charge, quick charge (BOOST), quick start * timer for quick charge *display of charging and starting current * protection against overloads and polarity reversal.

Technical Specifications:

• Mains Voltage: 230V, 1Ph
• Charge/Start Absorbed Power: 1.6/ 10 KW
• Voltage: 12-24 V
• Charge Current: 75 A
• Rated Charge Current: 50 A
• Starting Peak Current: 400 A
• Rated Reference Capacity (Min/Max): 20/1000 Ah 15h
• Weight: 21 Kg

Dynamic 620 Start

Battery charger and starter for charging free electrolyte batteries (WET) with 12/24V voltage and starting all kinds of cars, vans and light trucks. Characteristics: choice of normal charge, quick charge (BOOST), quick start * timer for quick charge * display of charging and starting current * protection against overloads and polarity reversal.

Technical Specifications:

• Mains Voltage: 230V, 1Ph
• Charge/Start Absorbed Power: 2/ 10 KW
• Voltage: 12-24 V
• Charge Current: 90 A
• Rated Charge Current: 70 A
• Starting Peak Current: 570 A
• Rated Reference Capacity (Min/Max): 20/1550 Ah 15h
• Weight: 25 Kg

Startronic 330

Digital, microprocessor controlled battery charger and starter for charging all types of batteries (WET, GEL, AGM), with 6/12/24V voltage and starting of cars, vans and trucks. Startronic protects the on-board electronic such as ABS, airbag, electronic injection, etc. Running modes: TEST, CHARGE,TRONIC, START and STAND-BY. The STAND-BY function is activated through connection to the cigarette lighter outlet of the car, it allows to disconnect and charge the car battery without erasing the preset values of the on-board computer. The TRONIC function allows for the electronic control of charging current, automatic interruption and restart. The new implemented technology SAFE START doesnot damage the on-board electronics during the starting phase (START) because it eliminates the overvoltages typical of the traditional starters. Characteristics: choice of charge current 1÷30A * display to check battery voltage, charging current and time * display to check battery status * protection against reverse polarity, battery failure, thermostatic interruption, faulty battery charger.

Technical Specifications:

• Main Voltage: 230V, 1Ph
• Current Range: 1-30 A
• Charge/Start Absorbed Power: 1.1/ 7 KW
• Voltage: 6-12-24 V
• Charge Current: 50 A
• Rated Charge Current: 30 A
• Starting Peak Current: 230 A
• Rated Reference Capacity (Min/Max): 10/450 Ah 15h
• Weight: 16.3 Kg

Startronic 530

Digital, microprocessor controlled battery charger and starter for charging all types of batteries (WET, GEL, AGM), with 6/12/24V voltage and starting of cars, vans and trucks. Startronic protects the on-board electronic such as ABS, airbag, electronic injection, etc. Running modes: TEST, CHARGE,TRONIC, START and STAND-BY. The STAND-BY function is activated through connection to the cigarette lighter outlet of the car, it allows to disconnect and charge the car battery without erasing the preset values of the on-board computer. The TRONIC function allows for the electronic control of charging current, automatic interruption and restart. The new implemented technology SAFE START doesnot damage the on-board electronics during the starting phase (START) because it eliminates the overvoltages typical of the traditional starters. Characteristics: choice of charge current 1÷40A * display to check battery voltage, charging current and time * display to check battery status * protection against reverse polarity, battery failure, thermostatic interruption, faulty battery charger.

Technical Specifications:

• Main Voltage: 230V, 1Ph
  
• Current Range: 1-40 A
• Charge/Start Absorbed Power: 1.5/ 9.5 KW
• Voltage: 6-12-24 V
• Charge Current: 75 A
• Rated Charge Current: 40 A
• Starting Peak Current: 400 A
• Rated Reference Capacity (Min/Max): 10/600 Ah 15h
• Weight: 19.5 Kg

SEM-25L

• Connection Diam: 25mm (1")
• Total Head: 35 m
• Delivery Volume: 115 L/min
• Max Suction Head: 8 m
• Engine: Mitsubishi TL33
• Engine Type: 2 Stroke Gasoline
• Fuel Tank Capacity: 0.6L
• Continuous Operating Time: 60min
• Dimensions: 310x255x 347 mm
• Weight: 6 Kg

SEH-50X

• Connection Diam: 50mm (2")
• Total Head: 30 m
• Delivery Volume: 600 L/min
• Max Suction Head: 8 m
• Engine: Honda GX-120
• Engine Type: 4 Stroke Gasoline
• Fuel Tank Capacity: 2L
• Continuous Operating Time: 2h
• Dimensions: 493x377x415 mm
• Weight: 24 Kg

SEH-80X

• Connection Diam: 80mm (3")
• Total Head: 26 m
• Delivery Volume: 930 L/min
• Max Suction Head: 8 m
• Engine: Honda GX-160
• Engine Type: 4 Stroke Gasoline
• Fuel Tank Capacity: 3.1L
• Continuous Operating Time: 2h 10min
• Dimensions: 530x399x473 mm
• Weight: 34 Kg

SE-50X

• Connection Diam: 50mm (2")
• Total Head: 30 m
• Delivery Volume: 600 L/min
• Max Suction Head: 8 m
• Engine: Robin EY15-3D
• Engine Type: 4 Stroke Gasoline
• Fuel Tank Capacity: 2.8L
• Continuous Operating Time: 2h 40min
• Dimensions: 489x340x435 mm
• Weight: 23 Kg

SE-80X

• Connection Diam: 80mm (3")
• Total Head: 26 m
• Delivery Volume: 930 L/min
• Max Suction Head: 8 m
• Engine: Robin EY20-3D
• Engine Type: 4 Stroke Gasoline
• Fuel Tank Capacity: 3.8L
• Continuous Operating Time: 3h
• Dimensions: 540x400x480 mm
• Weight: 30 Kg

SEV-50X

Technical Specifications:

• Connection Diam: 50mm (2")
• Total Head: 25 m
• Delivery Volume: 620 L/min
• Max Suction Head: 8 m
• Engine: Koshin K-180
• Engine Type: 4 Stroke Gasoline
• Fuel Tank Capacity: 3.6L
• Continuous Operating Time: 2h
• Dimensions: 514x410x426 mm
• Weight: 24.2 Kg

SEV-80X

• Connection Diam: 80mm (3")
• Total Head: 25 m
• Delivery Volume: 1050 L/min
• Max Suction Head: 8 m
• Engine: Koshin K-180
• Engine Type: 4 Stroke Gasoline
• Fuel Tank Capacity: 3.6L
• Continuous Operating Time: 1.6h
• Dimensions: 553x435x483 mm
• Weight: 27.7 Kg

SEM-50V

• Connection Diam: 50mm (2")
• Total Head: 50 m
• Delivery Volume: 500 L/min
• Max Suction Head: 8 m
• Engine: Mitsubishi GT-600
• Engine Type: 4 Stroke Gasoline
• Fuel Tank Capacity: 2.5L
• Continuous Operating Time: 2h
• Dimensions: 520x412x455 mm
• Weight: 25 Kg

SERM-50V

• Connection Diam: 50mm (2")
• Total Head: 90 m
• Delivery Volume: 500 L/min
• Max Suction Head: 8 m
• Engine: Mitsubishi GT-600
• Engine Type: 4 Stroke Gasoline
• Fuel Tank Capacity: 3.8 L
• Continuous Operating Time: 2h
• Dimensions: 565x460x483 mm
• Weight: 38 Kg

SE-80XD

• Connection Diam: 80mm (3")
• Total Head: 23 m
• Delivery Volume: 900 L/min
• Max Suction Head: 8 m
• Engine: Robin DY23-2D
• Engine Type: 4 Stroke Diesel
• Fuel Tank Capacity: 3.2L
• Continuous Operating Time: 3h
• Dimensions: 583x423x515 mm
• Weight: 50 Kg

STH-100X

KTH-80X

• Connection Diam: 80mm (3")
• Total Head: 27 m
• Delivery Volume: 1340 L/min
• Max Suction Head: 8 m
• Engine: Honda GX-240
• Engine Type: 4 Stroke Gasoline
• Fuel Tank Capacity: 5.3 L
• Continuous Operating Time: 2h 30min
• Dimensions: 721x516x586 mm
• Weight: 63 Kg

C-150 Centrifugal Pump

• Application:
  
•  
• Single impeller centrifugal pumps suitable to cover any small, medium or large capacity request; for domestic, agricultural and industrial purposes; with automatic water distribution through small and medium sized tanks; for sprinkler and flood irrigation systems in gardening and agriculture; to increase in derivation system pressure in aqueducts.
•  
• Operating Conditions:
  
•  
• Liquid temperature up to 60°C
  
• Ambient temperature up to 40°C
  
• Total suction lift up to 7 mt.
  
• Continuous duty
  
• 
  
• Motor:
  
•  
• Two-Pole induction motor
  
• (n = 2850 min-1)
  
• Insulation Class F
  
• Protection IP 44
  
• 
  
• Materials:
  
•  
• Pump body Cast Iron
  
• Motor Support Cast iron
  
• Impeller Stainless Steel
  
• Shaft with rotor Stainless Steel
  
• Mechanical seal Carbon/Ceramic
•  
• Technical Specifications:
  
•  
• Flow Rate: 125 l/min (7.5m³/h)
  
• Head: 36m
  
• Power: 1.1KW (1.5Hp)
  
• Voltage: 220V, 50Hz

C-200 Centrifugal Pump

• Application:
  
•  
• Single impeller centrifugal pumps suitable to cover any small, medium or large capacity request; for domestic, agricultural and industrial purposes; with automatic water distribution through small and medium sized tanks; for sprinkler and flood irrigation systems in gardening and agriculture; to increase in derivation system pressure in aqueducts.
•  
• Operating Conditions:
  
•  
• Liquid temperature up to 60°C
  
• Ambient temperature up to 40°C
  
• Total suction lift up to 7 mt.
  
• Continuous duty
  
• 
  
• Motor:
  
•  
• Two-Pole induction motor
  
• (n = 2850 min-1)
  
• Insulation Class F
  
• Protection IP 44
  
• 
  
• Materials:
  
•  
• Pump body Cast Iron
  
• Motor Support Cast iron
  
• Impeller Stainless Steel
  
• Shaft with rotor Stainless Steel
  
• Mechanical seal Carbon/Ceramic
•  
• Specifications:
  
•  
• Flow Rate: 125 l/min (7.5m3/h)
  
• Head: 43m
  
• Power: 1.5KW (2Hp)
  
• Voltage: 220V, 50Hz

DIG-2 Trash Pump

• Application:
•  
• Selfpriming monoblock water pumps with open impeller. The check valve inside the suction outlet avoids the syphon effect when stopping and assures the automatic re-start each time. The pump selfprimes even if partially filled and if the suction hose is completely empty. Suitable to drain clean or slightly dirty water and in flood irrigation systems.
•  
• Operating Conditions:
• Liquid temperature up to 60°C
• Ambient temperature up to 40°C
• Total suction lift up to 7 mt.
• Continuous duty
•  
• Motor:
•  
• Two-Pole induction motor
• (n = 2850 min-1)
• Insulation Class F
• Protection IP 44
•  
• Materials:
•  
• Pump body Cast Iron
• Motor Support Cast iron
• Impeller Cast Iron
• Shaft with rotor Stainless Steel
• Mechanical seal Carbon/Ceramic
•  
• Technical Specifications:
•  
• Flow Rate: 600 l/min (36m3/h)
• Head: 19m
• Power: 1.5KW (2Hp)
• Voltage: 220V, 50Hz

JET-202 Pump

• Application:
  
•  
• Selfpriming jet water pumps with a very high hydraulic performance and a considerable pressure capacity. Able to pump up to mt. 8 depth and work perfectly even in soda-water. Suitable for water lifting and distribution in domestic fittings by small and medium sized tanks.
•  
• Operating Conditions:
  
•  
• Max. working pressure 8 bar
  
• Liquid temperature up to 35°C
  
• Ambient temperature up to 40°C
  
• Total suction lift up to 8 mt.
  
• Continuous duty
  
• 
  
• Motor:
  
•  
• Two-Pole induction motor
  
• (n = 2850 min-1)
  
• Insulation Class F
  
• Protection IP 44
  
• 
  
• Materials:
  
•  
• Pump body Cast Iron
  
• Motor Support Cast Iron
  
• Impeller Brass
  
• Diffuser Noryl
  
• Pump flange Stainless Steel
  
• Shaft with rotor Stainless Steel
  
• Mechanical seal Carbon/Ceramic
• 
  
• Technical Specifications:
  
•  
• Flow Rate: 150 l/min (9m3/h)
  
• Head: 47m
  
• Power: 1.5KW (2Hp)
  
• Voltage: 400V- 3Ph, 50Hz 

VG-60 Multistage Pump

• Application:
  
•  
• Centrifugal vertical multistage water pumps able to develop high pressure and a high water lift with a comparatively low power consumption. Universal pump for civil and industrial purposes, for high pressure system and for irrigation in agriculture and sports fittings.
•  
• Operating Conditions:
• 
  
• Max Working Pressure: 10 Bar
• Liquid temperature up to 35°C
  
• Ambient temperature up to 40°C
  
• Total suction lift up to 7 mt.
  
• Continuous duty
  
• 
  
• Motor:
  
•  
• Two-Pole induction motor
  
• (n = 2850 min-1)
  
• Insulation Class F
  
• Protection IP 55
  
• 
  
• Materials:
  
•  
• Pump body Cast Iron
  
• Motor Support Cast iron
  
• Impeller Noryl
• Diffuser Noryl
• Pump Casing Stainless Steel
  
• Shaft with rotor Stainless Steel
  
• Mechanical seal Silicon/Silicon
•  
• Technical Specifications:
  
•  
• Flow Rate: 160 l/min (9.6m3/h)
  
• Head: 73m
  
• Power: 2.2KW (3Hp)
  
• Voltage: 220V, 50Hz

VGT-80 Multistage Pump

• Application:
• 
  
• Centrifugal vertical multistage water pumps able to develop high pressure and a high water lift with a comparatively low power consumption. Universal pump for civil and industrial purposes, for high pressure system and for irrigation in agriculture and sports fittings.
•  
• Operating Conditions:
  
•  
• Max Working Pressure: 10 Bar
• Liquid temperature up to 35°C
  
• Ambient temperature up to 40°C
  
• Total suction lift up to 7 mt.
  
• Continuous duty
  
• 
  
• Motor:
  
•  
• Two-Pole induction motor
  
• (n = 2850 min-1)
  
• Insulation Class F
  
• Protection IP 55
  
• 
  
• Materials:
  
•  
• Pump body Cast Iron
  
• Motor Support Cast iron
  
• Impeller Noryl
• Diffuser Noryl
• Pump Casing Stainless Steel
  
• Shaft with rotor Stainless Steel
  
• Mechanical seal Silicon/Silicon
•  
• Technical Specifications:
  
•  
• Flow Rate: 180 l/min (10.8m3/h)
  
• Head: 97m
  
• Power: 3KW (4.0Hp)
  
• Voltage: 400V, 50Hz

A-115 Submersible Semi-Trash Pump

• Motor Power : 1 HP 0.75 KW
• Connection Diameter: 2” (50mm)
• Frequency: 50 Hz
• Number Of Phases: 1
• Number of Poles: 2
• RPM: 2850
• Std. Head: 12 M
• Std. Flow: 0.15 M3/ min
• Max. Flow: 0.25 M3/min
• Weight: 18 Kg

B-112 Submersible Trash Pump

• Motor Power : 1 HP 0.75 KW
• Connection Diameter: 2” (50mm)
• Frequency: 50 Hz
• Number Of Phases: 1
• Number of Poles: 2
• RPM: 2850
• Std. Head: 8 M
• Std. Flow: 0.19 M3/ min
• Max. Flow: 0.35 M3/min
• Weight: 20 Kg

B-333 Submersible Trash Pump

Technical Specifications:

• Motor Power : 3 HP 2.2 KW
• Connection Diameter: 3” (80mm)
• Frequency: 50 Hz
• Number Of Phases: 3
• Number of Poles: 2
• RPM: 2850
• Std. Head: 11 M
• Std. Flow: 0.4 M3/ min
• Max. Flow: 0.9 M3/min
• Weight: 41 Kg

B-353 Submersible Trash Pump

• Motor Power : 5 HP 3.7 Kw
• Connection Diameter: 3” (80mm)
• Frequency: 50 Hz
• Number Of Phases: 3
• Number of Poles: 2
• RPM: 2850
• Std. Head: 14 M
• Std. Flow: 0.5 M3/ min
• Max. Flow: 1.1 M3/min
• Weight: 45 Kg

High Pressure Pump 170 Bar

• Model: XM 11.17 N
• Pressure: 170 bar (2500 psi)
• Flow Rate: 11 l/min (2.90 gpm)
• Power Required: 5 hp (3.7 Kw)
• RPM: 1450
• Shaft: Solid Shaft Pump (male)
• Shaft Diam: 24mm (Keyway)
• Pump: N Version
• Code: 7900
• Weight: 6.5Kg

High Pressure Pump 200 Bar

• Model: RK 15.20 H N
• Pressure: 200 bar (2900 psi)
• Flow Rate: 15 l/min (3.96 gpm)
• Power Required: 7.5 hp (7.5 Kw)
• RPM: 1450
• Shaft: Solid Shaft Pump (male)
• Shaft Diam: 24mm (Keyway)
• Pump: N Version
• Code: 20638
• Weight: 9 Kg

Bypass Valve For 170 Bar Pump

• Pressure regulating unloader valve, automatically relieves pressure from pump at shut-off, built-in by-pass
•  
• Technical Specifications:
•  
• Model: COD.20080
• Max. Pressure: 250 bar
• Max Flow Rate: 35 L/min
• Inlet: ½”G (F)
• Outlet: ⅜” G (M)

Bypass Valve For 200 Bar Pump

• Pressure regulating unloader valve, automatically relieves pressure from pump at shut-off, built-in by-pass
•  
• Technical Specifications:
•  
• Model: COD.22308
• Max. Pressure: 300 bar
• Max Flow Rate: 35 L/min
• Inlet: ½”G (F)
• Outlet: ⅜” G (M)

Zumba

Technical Specifications:

• Pressure: 110 Bar
• Flow Rate: 5.5L/min

House

• - Three steel pistons, aluminium axial pump head with built-in by-pass valve
• - Automatic Stop System
• - Trolley with ergonomic handle
• - Power cable with plug
•  
• Standard Equipment:
•  
• - Gun with quick connection
• - 6m high pressure hose
• - High pressure lance with fan jet
• - Turbo lance
• - Foam lance + bottle
• - Patio cleaner
•  
• Technical Specifications:
•  
• Max. Pressure: 120 bar (1740 psi)
• Flow Rate: 5.5 L/min
• Power: 1.7 Kw 2.2 Hp
• Voltage: 230V~50Hz
• Weight: 6.5 Kg
• Volume: 0.05 M3 

Rumba 140

• - Three steel pistons, aluminium axial pump head with built-in by-pass valve
• - Automatic Stop System
• - Ergonomic handle with accessory holder
• - Cable holder
•  
• Standard Equipment:
•  
• - Gun with quick connection
• - 6m high pressure hose
• - Adjustable fan jet lance
• - Turbo lance
• - Foam lance
•  
• Technical Specifications:
•  
• Max. Pressure: 140 bar (2030 psi)
• Flow Rate: 7.5 L/min
• Power: 1.9 Kw 2.54 Hp
• Voltage: 230V~50Hz

Rumba 160

• - Three pistons, aluminium pump head with built-in by-pass valve
• - Automatic Stop System
• - Ergonomic handle with accessory holder
• - Cable holder
• - Hose Reel
•  
• Standard Equipment:
•  
• - Gun with quick connection
• - 8m high pressure hose
• - Adjustable fan jet lance
• - Turbo lance
• - Foam lance
• - Rotary brush
•                          
• Technical Specifications:
•  
• Max. Pressure: 160 bar (2320 psi)
• Flow Rate: 8.5 L/min
• Power: 2.5 Kw 3.35 Hp
• Voltage: 230V~50Hz

Groove

Technical Specifications:

• Pressure: 140 Bar
• Flow Rate: 6.75L/min

Fox

• - Three steel pistons, aluminium axial pump head with built-in by-pass valve
• - Automatic Stop System
• - Trolley with ergonomic handle with accessory holder
• - Detergent built-in tank for direct suction
• - Hose holder
• - Cable holder
• - Side holder to site lance and gun matched together (ready for use)
•  
• Standard Equipment:
•  
• - Gun with quick connection
• - 8m high pressure hose
• - High pressure lance with adjustable fan jet plus high/low pressure regulation
• - Turbo lance
•  
• Technical Specifications:
•  
• Max. Pressure: 145 bar (2103 psi)
• Flow Rate: 8 L/min
• Power: 2.4 Kw 3.21 Hp
• Voltage: 230V~50Hz

Progressive

• - Three steel pistons, brass pump head with built-in by-pass valve
• - Full assembled (ready for use)
• - Trolley with ergonomic handle and accessory holder
• - Detergent built-in tank for direct suction
• - Hose holder, cable holder
• - Side holder to site lance and gun matched together (ready for use)
• - Automatic stop system
•  
• Standard Equipment:
•  
• - Gun with quick connection
• - Steel Reinforced high pressure hose 8m
• - Metal lance with quick connection 4 nozzle set
• - Turbo lance
•  
• Technical Specifications:
•  
• Max. Pressure: 160 bar (2320 psi)
• Flow Rate: 8.5 L/min
• Power: 2.8 Kw 3.8 Hp
• Voltage: 230V~50Hz

The Kranzle 2+2

• Model: The Kranzle 2+2
• Working Width: 80cm
• Storage Bin: 40L

Explorer 2015 LP

• - 4 poles electrical motor (1450 RPM) with thermal protection and water cooling
• - Three ceramic pistons brass linear pump head with built-in by-pass valve
• - Suction and delivery S/S valves
• - Automatic Stop (late shut down protection 24V)
• - Safety valve for overpressure
• - Integrated detergent suction with external suction probe
• - Power cable (5m)
• - Pressure regulator
• - Glicerine pressure gauge
• - Tough steel main frame
•  
• Standard Equipment:
•  
• - High pressure gun
• - High pressure lance with fan jet
• - High pressure hose 10 m
•  
• Technical Specifications:
•  
• Pressure: 30-200 bar
• Flow Rate: 450-900 L/h
• Power: 7 Kw 9.37 Hp
• RPM: 1450
• Voltage: 400V~50Hz

Sundeck 5 31Y

• - 4 poles electrical motor (1450 RPM) with thermal protection and water cooling (three phase models)
• - Three ceramic coated pistons brass axial pump head (Sundek 31Y) full ceramic piston (Sundek 55Y-75Y), brass linear pump head with high thermal efficiency steel oil
• - Vertical burner with high thermal efficiency steel oil
• - Suction and delivery S/S valves
• - Safety valve
• - Temperature regulation gauge
• - Glicerine pressure gauge
• - Automatic Stop System late shut down protection 24V
• - Adjustable detergent delivery with built-in tank for indirect suction
• - Two ways fuel pump
• - Low fuel lamp
• - Ergonomic handles and impact resistant covers
• - Accessory holder
• - Power cable (5 m)
•  
• Standard Equipment:
• 
  
• - High pressure gun with rotating coupling
• - High pressure S/S lance with high/low pressure regulation
• - High pressure hose 10 m
• - Inlet brass quick fitting
• - High pressure nozzle
• - Outlet-hose quick fitting
• - Header tank
•  
• Technical Specifications:
•  
• Pressure: 30-110 bar
• Flow Rate: 330-660 L/h
• Max. Water Temperature: 140˚C
• Power: 3 Kw 4 Hp
• RPM: 1450
• Voltage: 230V~50Hz

Sundeck 5 55Y

• - 4 poles electrical motor (1450 RPM) with thermal protection and water cooling (three phase models)
• - Three ceramic coated pistons brass axial pump head (Sundek 31Y) full ceramic piston (Sundek 55Y-75Y), brass linear pump head with high thermal efficiency steel oil
• - Vertical burner with high thermal efficiency steel oil
• - Suction and delivery S/S valves
• - Safety valve
• - Temperature regulation gauge
• - Glicerine pressure gauge
• - Automatic Stop System late shut down protection 24V
• - Adjustable detergent delivery with built-in tank for indirect suction
• - Two ways fuel pump
• - Low fuel lamp
• - Ergonomic handles and impact resistant covers
• - Accessory holder
• - Power cable (5 m)
•  
• Standard Equipment:
•  
• - High pressure gun with rotating coupling
• - High pressure S/S lance with high/low pressure regulation
• - High pressure hose 10 m
• - Inlet brass quick fitting
• - High pressure nozzle
• - Outlet-hose quick fitting
• - Header tank
•  
• Technical Specifications:
•  
• Pressure: 30-150 bar
• Flow Rate: 450-900 L/h
• Max. Water Temperature: 140˚C
• Power: 5.5 Kw 7.37 Hp
• RPM: 1450
• Voltage: 4000V~50Hz

Sundeck 5 75Y

• - 4 poles electrical motor (1450 RPM) with thermal protection and water cooling (three phase models)
• - Three ceramic coated pistons brass axial pump head (Sundek 31Y) full ceramic piston (Sundek 55Y-75Y), brass linear pump head with high thermal efficiency steel oil
• - Vertical burner with high thermal efficiency steel oil
• - Suction and delivery S/S valves
• - Safety valve
• - Temperature regulation gauge
• - Glicerine pressure gauge
• - Automatic Stop System late shut down protection 24V
• - Adjustable detergent delivery with built-in tank for indirect suction
• - Two ways fuel pump
• - Low fuel lamp
• - Ergonomic handles and impact resistant covers
• - Accessory holder
• - Power cable (5 m)
•  
• Standard Equipment:
•  
• - High pressure gun with rotating coupling
• - High pressure S/S lance with high/low pressure regulation
• - High pressure hose 10 m
• - Inlet brass quick fitting
• - High pressure nozzle
• - Outlet-hose quick fitting
• - Header tank
•  
• Technical Specifications:
•  
• Pressure: 30-200 bar
• Flow Rate: 450-900 L/h
• Max. Water Temperature: 140˚C
• Power: 7.3 Kw  9.37 Hp
• RPM: 1450
• Voltage: 4000V~50Hz

K 7/120

Technical Specifications:

• Operating Pressure: 30-120 bar (continuously adjustable)
• Admissible Overpressure: 135 bar
• Water Output: 7 l/min
• Inlet Water Temperature: max 60^oC
• Steel Weave High Pressure Hose: 10 m
• Dirtkiller: Optional
• Connected Load: 230V, 50Hz
• Power Input: 1.6 KW @1400 rpm
• Weight Incl. Accessories: 22 Kg

K 1152 TS T

Technical Specifications:

• Operating Pressure: 30-130 bar (continuously adjustable)
• Admissible Overpressure: 150 bar
• Water Output: 10 l/min
• Inlet Water Temperature: max 60^oC
• Hose Drum: Yes
• Steel Weave High Pressure Hose: 15 m
• Dirtkiller: Yes
• Detergent Injector: Yes
• Connected Load: 230V, 50Hz
• Power Input: 2.8 KW
• Weight Incl. Accessories: 26 Kg

Quadro 170 TS T

Technical Specifications:

• Operating Pressure: 30-170 bar (continuously adjustable)
• Admissible Overpressure: 190 bar
• Water Output: 9 l/min
• Content Water Tank: 7 l
• Inlet Water Temperature: max 60^oC
• Hose Drum: Yes
• Steel Weave High Pressure Hose: 15 m
• Dirtkiller: Yes
• Detergent Injector: Yes
• Connected Load: 230V, 50Hz
• Power Input: 3.2 KW @1400 rpm
• Weight Incl. Accessories: 45 Kg

Quadro 800 TS T

Technical Specifications:

• Operating Pressure: 30-250 bar (continuously adjustable)
• Admissible Overpressure: 270 bar
• Water Output: 13.3 l/min
• Inlet Water Temperature: max 60^oC
• Volume Water Tank: 16L
• Suction Height: 2.5m
• Steel Braided High Pressure Hose: 20 m
• Motor Speed: 1,400 rpm
• Power Intake: 7.5 KW
• Power Output: 5.5 KW
• Turbokiller: Yes
• Detergent Injector: Yes
• Connected Load: 400V, 3Ph, 50Hz
• Weight: 89 Kg
• Dimensions: 770 x 570 x 990mm

B 170 T

Technical Specifications:

• Operating Pressure: 30-150 bar (continuously adjustable)
• Admissible Overpressure: 170 bar
• Water Output: 12.5 l/min
• Inlet Water Temperature: max 60^oC
• Suction Height: 2.5m
• Steel Braided High Pressure Hose: 20 m
• Engine Power: 5.5HP Petrol Honda
• Turbokiller: Yes
• Detergent Injector: Yes
• Water Intake Filter: Yes
• Weight: 68 Kg
• Dimensions: 720 x 570 x 960mm

B 270 T

Technical Specifications:

• Operating Pressure: 30-250 bar (continuously adjustable)
• Admissible Overpressure: 270 bar
• Water Output: 16 l/min
• Inlet Water Temperature: max 60^oC
• Suction Height: 2.5m
• Steel Braided High Pressure Hose: 20 m
• Engine Power: 13HP Petrol Honda
• Turbokiller: Yes
• Detergent Injector: Yes
• Water Intake Filter: Yes
• Weight: 93 Kg
• Dimensions: 720 x 570 x 960mm

Sandblaster Set

• - Sand blasting set for Kranzle high pressure cleaners 1151 T, Quadro 800 TS T, B 170 T, B 270 T
• - Min flow required 10 L/min

Windy 365 IR

Wet & Dry Vacuum Cleaner

• 3 Motors
• Motor Power: 3000 W (max 3600)
• Tank Capacity: 78 L
• Suction Air: 162 l/s
• Voltage: 230V /50Hz

Windy Foam

• Motor Power: 2 - 2000W (max 2400W)
• Tank Capacity: 65/30/40L
• Suction Air: 130 l/s
• Voltage: 220/240V - 50/60Hz

Windy Foam Compressor

• Motor Power: 2 - 2000W (max 2400W)
• Tank Capacity: 65/30/40L
• Suction Air: 130 l/s
• Voltage: 220/240V - 50/60Hz

KJ-2200

Technical Specifications:

• Flow: 9L/min
• Max Pressure: 150 bar
• Gasoline Engine: 5.5Hp, 4 Stroke
• Engine Type: Honda GX160
• Hose Length: 33m 
• Hose Size: 1/4"
• Cleaning Capacity: Up to 6" Lines

Standard Equipment:

• - 23m x 1/8" Hose
• - FV-1 Foot Valve
• - Propulsion Nozzle 1/4"
• - Penetrating Nozzle 1/4"
• - Propulsion Nozzle 1/8"
• - Penetrating Nozzle 1/8"
• - Drop Head Nozzle 1/8"

KJ-3100

Technical Specifications:

• Flow: 21L/min
• Max Pressure: 205 bar
• Gasoline Engine: 16Hp, 4 Stroke
• Engine Type: Vanguard by B&S
• Hose Length: 61m 
• Hose Size: 3/8"
• Cleaning Capacity: Up to 10" Lines

Standard Equipment:

• - H-111 and H-112 1/4" NPT Nozzles
• - H-38 Hose Reel with 200' (61m) x 3/8" ID Jet Hose
• - 50' (15m) x 3/8" ID Jet/Wash Hose
• - FV-1 Foot Valve
• - Nozzle Cleaning Tool
• - HW-30 Wash Wand

K 1152 TS T

Technical Specifications:

• Operating Pressure: 30-130 bar (continuously adjustable)
• Admissible Overpressure: 150 bar
• Water Output: 10 l/min
• Inlet Water Temperature: 60^oC
• Hose Drum: Yes
• Steel Weave High Pressure Hose: 15 m
• Dirtkiller: Yes
• Detergent Injector: Yes
• Connected Load: 230V, 50Hz
• Power Input: 2.8 KW
• Weight Incl. Accessories: 26 Kg

Water Jetting Accessories:

• - 30m Pipe cleaning hose
• - Propulsion Nozzle KN045
• - Penetrating Nozzle KNF045
• - Ball Head Nozzle KK045
• - Ball Head Nozzle KKF045
• - Rotating Pipe Cleaning Nozzle KNR045

Quadro 800 TS T

Technical Specifications:

• Operating Pressure: 30-250 bar (continuously adjustable)
• Admissible Overpressure: 270 bar
• Water Output: 13.3 l/min
• Inlet Water Temperature: max 60^oC
• Volume Water Tank: 16L
• Suction Height: 2.5m
• Steel Braided High Pressure Hose: 20 m
• Motor Speed: 1,400 rpm
• Power Intake: 7.5 KW
• Power Output: 5.5 KW
• Turbokiller: Yes
• Detergent Injector: Yes
• Connected Load: 400V, 3Ph, 50Hz
• Weight: 89 Kg
• Dimensions: 770 x 570 x 990mm

Water Jetting Accessories:

• - 30m Pipe cleaning hose
• - Propulsion Nozzle KN045
• - Penetrating Nozzle KNF045
• - Ball Head Nozzle KK045
• - Ball Head Nozzle KKF045
• - Rotating Pipe Cleaning Nozzle KNR045

B 170 T

Technical Specifications:

• Operating Pressure: 30-150 bar (continuously adjustable)
• Admissible Overpressure: 170 bar
• Water Output: 12.5 l/min
• Inlet Water Temperature: max 60^oC
• Suction Height: 2.5m
• Steel Braided High Pressure Hose: 20 m
• Engine Power: 5.5HP Petrol Honda
• Turbokiller: Yes
• Detergent Injector: Yes
• Water Intake Filter: Yes
• Weight: 68 Kg
• Dimensions: 720 x 570 x 960mm

Water Jetting Accessories:

• - 30m Pipe cleaning hose
• - Propulsion Nozzle KN045
• - Penetrating Nozzle KNF045
• - Ball Head Nozzle KK045
• - Ball Head Nozzle KKF045
• - Rotating Pipe Cleaning Nozzle KNR045

B 270T

Technical Specifications:

• Operating Pressure: 30-250 bar (continuously adjustable)
• Admissible Overpressure: 270 bar
• Water Output: 16 l/min
• Inlet Water Temperature: max 60^oC
• Suction Height: 2.5m
• Steel Braided High Pressure Hose: 20 m
• Engine Power: 13HP Petrol Honda
• Turbokiller: Yes
• Detergent Injector: Yes
• Water Intake Filter: Yes
• Weight: 93 Kg
• Dimensions: 720 x 570 x 960mm

 Water Jetting Accessories:

• - 30m Pipe cleaning hose
• - Propulsion Nozzle KN045
• - Penetrating Nozzle KNF045
• - Ball Head Nozzle KK045
• - Ball Head Nozzle KKF045
• - Rotating Pipe Cleaning Nozzle KNR045

Water Jetting Hose

KN Nozzle

• - Pipe cleaning nozzle 1/8" inside thread
• - 3 jets to the back
• - Head diameter: 15mm

KNF Nozzle

• - Pipe cleaning nozzle 1/8" inside thread with front bore
• - 3 jets to the back
• - 1 jet to the front
• - Head diameter: 15mm

KN-KNF Back

KK Nozzle

• - Pipe cleaning nozzle, spherical head 1/4" inside thread
• - 4 jets to the back
• - Head diameter: 25mm
• - Available with reducing adaptor to fit 1/8" hose

KKF Nozzle

• - Pipe cleaning nozzle, spherical head with front bore, 1/4" inside thread
• - 4 jets to the back
• - 1 jet to the front
• - Head diameter: 25mm
• - Available with reducing adaptor to fit 1/8" hose

KK-KKF Back

KNR045 Nozzle

• - Rotary pipe cleaning nozzle 1/4" inside thread
• - 3 jets to the back
• - Head diameter: 18mm
• - Available with reducing adaptor to fit 1/8" hose

KNR Back

EH-12 Rammer Use

• Class: Overhead Valve for Rammer
• Max Power: 4.0 HP @ 4000rpm
• Continuous: 2.8 HP @ 3000rpm
• Fuel: Gasoline
  
• Starter: Recoil
  
• Dry Weight: 15 Kg
  

EY-20 3D

• Type: Air-cooled, 4-cycle, upright single cylinder
• Max Output: 5.0Hp @ 4000rpm
• Continuous Output: 3.0Hp @ 3000rpm, 3.5Hp @ 3600rpm
• Fuel: Gasoline
• Fuel Tank Capacity: 3.8L
  
• Starter: Recoil Start
• Dry Weight: 15.2 Kg

EY-28

 Technical Specifications:

•  Type: Air-cooled, 4-cycle, upright single cylinder
• Max Output: 7.5Hp @ 4000rpm
• Continuous Output: 5.5Hp @3600rpm
• Fuel: Gasoline
• Fuel Tank Capacity: 5.5L
• Starter: Recoil Start
• Dry Weight: 21 Kg

EX-17 Premium

 Technical Specifications:

• Type: Air-cooled, 4-cycle, slant single cylinder, OHC
  
• Max Output: 5.7Hp @ 4000rpm
• Continuous Output: 3.5Hp @3000rpm, 4.0Hp @3600rpm
• Fuel: Gasoline
• Fuel Tank Capacity: 3.2L
• Starter: Recoil Start
• Dry Weight: 15 Kg

EX-21 Premium

 Technical Specifications: